Main research subject
-
Wang Chiidi Experimental Study on the Continuous Wave Laser Treatment Applied to Corroded Steel Structures
-
Alan Kim Research on the surface properties of blasted steel
-
-
Kimori Sho SURFACE AND MECHANICAL PROPERTIES OF CARBON STEEL AFFECTED BY ROTATING CONTINUOUS WAVE LASER TREATMENT
-
Ichiro Dote Research on corrosion characteristics of spheroidal graphite cast iron in atmospheric environment
-
-
Rui Guo
-
Rifadli Bahsuan BONDING PROPERTIES OF CFRP STRAND SHEET AND CFRP PLATE ON RC BEAM
-
FATIGUE BEHAVIOR OF ROOT CRACK AND STRUCTURAL RESPONSE IN ORTHOTROPIC STEEL DECKS
-
-
Tatsuro Sakamoto Research on undercoat corrosion phenomena of steel structures in highly corrosive environments and methods for improving anticorrosion performance
-
Nariaki Tsukamoto Research on non-destructive diagnostic methods for fatigue and corrosion damage in steel decks and the priority of countermeasures
-
-
Shuji Ishihara Research on sacrificial anodic corrosion protection technology for steel structures in atmospheric corrosion environments
-
-
Young Soo Jeong ASSESSMENT ON FIGURATION OF TIME-DEPENDENT CORRODED SURFACE AND STRESS CONCENTRATION EFFECT FOR STEEL STRUCTURAL MEMBER UNDER ATMOSPHERIC ENVIRONMENT
-
RESIDUAL STRUCTURAL PERFORMANCE OF A STEEL PLATE GIRDER BRIDGE WITH LOCAL CORROSION
-
Yoshihiro Ito
-
-
Kengo Katsura Research on road maintenance management based on service evaluation
-
Tomohisa Choi Research on strength evaluation of structural members using short fiber reinforced lightweight type 2 concrete
-
-
Kazuaki Yokoyama Research on efficiency improvement of maintenance and management of road bridge concrete structures and performance evaluation of cross-section repair and reinforcement construction methods
-
Susumu Iguchi Research on rationalization of steel deck structure and improvement of fatigue durability
-
Kenji Kobayashi Research on mechanical properties and durability of glass fiber reinforced plastic pultruded parts
-
-
Arwin Amiruddin A STUDY ON SEISMIC RETROFIT DESIGN OF EXISTING RC BRIDGE PIERS USING CFRP GRID AND PCM SHOTCRETE
-
-
Shenghua Guo FUNDAMENTAL STUDY ON APPLICATION OF UNRESIN CONTINUOUS CARBON FIBER REINFORCING SYSTEM TO CONCRETE STRUCTURE
-
Naofumi Hosomi Research on evaluation and prediction of corrosion behavior and fatigue durability at the concrete interface of steel members
-
-
Tomio Tomoda Research on the stress transmission mechanism and design method of the corners of composite rigid frame bridge piers with upper and lower rigid connections
-
-
Rudy Djamaluddin FUNDAMENTAL STUDY ON APPLICATION OF UNRESIN CONTINUOUS CARBON FIBER REINFORCING SYSTEM TO CONCRETE STRUCTURE
-
Tadahiko Tsutsumi
-
-
Xu Shengzhuo Research on bridge axial joints of road bridge composite floor slabs using high-strength bolt tension joints
-
Lee Jung-hwan Research on elasto-plastic behavior and seismic verification of multi-column composite structure bridge piers using concrete-filled steel pipes
-
-
Kohei Yamaguchi
-
Basem Abullah FUNDAMENTAL STUDY ON STRENGTHENING OF STEEL GIRDER BRIDGE WITH RC SLAB BY USING PULTRUDED GFRP MEMBERS
-
Tetsuo Shirai
-
Koji Harada
-
-
Takashi Nagahama Fundamental research on application to hardening and non-hardening continuous carbon fiber concrete members
-
-
Eiki Enbayashi Fundamental research on dynamic ultimate deformation characteristics of prestressed concrete beams
-
Norio Ogata Experimental research on seismic reinforcement methods for reinforced concrete piers with stepped sections using carbon fiber sheets
-
Takayuki Murayama Fundamental research on landscape and design methods for strong steel piers of urban viaducts with curved surfaces at each corner
-
-
Motoobuchi Research on fracture behavior of reinforced concrete deep beams and shear strength calculation method
-
Nobuyuki Kono Research on creep characteristics of steel plate/concrete composite plate with prestress introduced in two directions
-
Takeshi Yamada Research on the structural characteristics of synthetic slab bridges using lightweight fillers and their applications
-
-
Tang Jialin Fundamental research on the structural characteristics of multi-column composite bridge piers using concrete-filled circular tubular columns
-
Kazutaka Kobayashi Basic research on impact behavior and safety verification of precast concrete guard fences
-
-
Shigeo Shinnishi Fundamental research on the introduction of bidirectional prestress in steel plate/concrete composite slab structures
-
-
Ichiro Kuroda Fundamental research on heat conduction and temperature stress in reinforced concrete beams and steel-concrete composite beams subjected to high temperature loads
-
Li Jingdong Fundamental research on fatigue behavior of synthetic slabs with three-dimensional truss-type dowels
-
-
Keisuke Suzuki Evaluation of the effect of coating thickness on electrochemical interaction between coating scratches on steel
-
Aoyuki Tanaka Fundamental research on the effects of volcanic plume and airborne sea salt on the progress of steel corrosion during rocket launch
-
Kaiji Takagi Fundamental research on the applicability of sacrificial anodic corrosion protection technology in closed cross-section water retention areas
-
Ryohei Toyoda Fundamental research on the surface characteristics of steel materials using steel substrate conditioning technology using a multiphase fluid of abrasives and ultrahigh-pressure water
-
-
LIU WEIJIE Fundamental study on the bond behavior and deterioration characteristics of CFRP strengthened steel structure
-
Saki Okada
-
-
Shoma Iio Proposal of an electrochemical surface preparation method for severely corroded members based on the elucidation of the corrosion product reduction mechanism by atmospheric sacrificial anodic corrosion protection technology
-
Ryo Higuchi Research on quantitative evaluation of corrosion progression based on elucidation of electrochemical mutual interference of steel corrosion between adjacent paint film scratches
-
Ryo Inoue Fundamental research on the elucidation of the electrochemical protection mechanism for steel corrosion between cracks in heavy-duty anti-corrosion coating
-
Yang Haoxuan Fundamental research on the durability and anti-corrosion properties of the interface between Al/Zn-based thermal spray coating with artificial defects and heavy-duty anti-corrosion coating
-
Xie Jiajing Fundamental study on the epoxy deterioration and galvanic corrosion in CFRP strengthened steelstructures
-
Park Sanghong Fundamental study on steel surface properties under various AWJ treatment conditions
-
-
Anti-corrosion Behavior of Hot-dip Al and 55Al-Zn Coatings on Steel Structures
-
Liu Shaobo Fundamental research on corrosion resistance and anticorrosion performance in the interface between Al-5Mg alloy thermal spraying and heavy anticorrosion coating
-
Takashi Hasegawa Basic research on the electrochemical mechanism of steel corrosion between multiple coating scratches and its evaluation method
-
Tomoki Takeda Research on atmospheric sacrificial anodic corrosion protection using Al-based anode plate and fiber sheet for Al-5Mg alloy thermal spray coating
-
Yasuki Miyazaki Basic research on the anticorrosion effect of zinc-rich paint against steel corrosion between paint film scratches
-
Takeshi Kaneko Fundamental research on the effect of laser treatment on the mechanical properties and coating adhesion performance of steel
-
SUN XIAOTONG Research on improving the accuracy of evaluating the corrosion rate of steel materials at the ground level of steel structures
-
-
Shunta Sakurai Research on improving adhesion performance in prefabricated CFRP plate adhesion reinforcement method using polyurea resin
-
Ikuo Tadakuma Experimental research on the crimping joint method for the corners of split precast box culverts
-
Keita Tanigawa Research on elucidation of the electrochemical mechanism of steel member corrosion between multiple paint film scratches and spatio-temporal statistical simulation
-
Du Jinxuan Basic research on corrosion resistance and anti-corrosion properties in the interface between Al-5Mg alloy thermal spraying and heavy anti-corrosion coating
-
Kazuya Yamashita Research on sacrificial anodic corrosion protection technology using Al-Zn alloy materials and water-absorbing/water-retaining fibers for steel structures in atmospheric environments
-
-
Masaya Ishimura Experimental research on pressure bonding of precast box culvert corners using high-strength reinforcing bars
-
Hiroshi Ogiimprovement of adhesion performance by inserting polyurea resin in CFRP plate adhesion reinforcement method
-
Gaku Masumoto: Fundamental research on the electrochemical mechanism of steel corrosion between adjacent paint film scratches
-
Hiroyuki Momota: Basic research on the corrosion behavior of steel finger plates and the applicability of sacrificial song anti-corrosion technology
-
Kosuke Yagi Research on evaluation of corrosion resistance and anticorrosion performance of hot-dip aluminum plated steel structures
-
Aran Kim Fundamental research on the effect of blast surface preparation on the surface properties and corrosion properties of steel
-
-
Minami Hirao Research on corrosion evaluation methods at the structural part level of steel structures
-
Takushi Fujimoto Research on the applicability of atmospheric sacrificial anodic corrosion protection technology using Al-Zn anode materials and fiber sheets to steel structures
-
Shoma Yamashita Analytical research on the fixing mechanism of post-installed metal anchors
-
Masahiro Watanabe Experimental research on the joining method for the corners of precast box culverts
-
Ryota Watanabe Fundamental study on the effects of surface preparation conditions on steel surface properties and coating adhesion performance
-
-
Takuya Okamoto Static and fatigue properties of RC members flexurally reinforced using highly durable resin concrete panels
-
Aki Kanamaru Experimental study on reinforcement effect by PCM spraying method for low rebar ratio RC beams with joints
-
Yu Gan Physical properties of CFRP rods and RC beams using CFRP rods
-
Junji Kobayashi Time-dependent corrosion damage simulation of steel members considering the complexities of paint film scratches and deterioration and their electrochemical mechanisms
-
Yohei Tsuchibashi Research on the corrosion behavior of steel materials at the ground level of steel structures and its evaluation method
-
Masatsugu Michino Research on evaluation method of corrosion behavior over time of unpainted weathering steel by corrosion product layer
-
Xiaolong Guo Fundamental research on corrosion resistance and corrosion resistance properties of Al/Mg alloy thermal spraying and heavy-duty anti-corrosion coating
-
-
Hiroki Goda Fundamental research on the degradation behavior of thermal spraying, painting, and plating films with artificial defects in salt-damaged environments
-
Kohei Ibusuki Evaluation of the impact of corrosion damage on the fatigue durability of steel deck deck plates
-
Yosuke Hori Research on the design, construction and maintenance of composite slab bridges that can withstand the load of large aircraft
-
Zhou Aixin Research on the load-bearing characteristics of precast arch culverts by PC crimping and the bending characteristics of joints
-
-
Rui Guo Shear reinforcement effect of RC beams with haunches by PCM spraying method using CFRP grid
-
Masaru Kinoshita Research on methods for evaluating and predicting corrosion behavior at the ground level of steel structural members and anti-corrosion methods
-
Takefumi Shigeto Bending reinforcement effect of unreinforced concrete beams with joints by PCM spraying method
-
Daiki Takushima Development of GFRP Bridge Expansion Device
-
Hideyuki Hayashi Research on evaluation methods for corrosion behavior of steel members over time considering coating film defects
-
Taiga Hirai: Fundamental research on fatigue damage in the remaining parts of lifting hardware for erection of steel floor slabs
-
-
Kazuhiro Utsunomiya Research on methods for evaluating the corrosion behavior of steel members over time, starting from coating film defects
-
Du Jinwei Effect on fatigue behavior of out-of-plane gusset welded joints with one-sided fillet welds
-
Kazuya Matsuo Research on the corrosion behavior of steel structural members at the concrete ground and its countermeasures
-
-
Yusuke Kato Fundamental research on critical corrosion damage sites for load-bearing capacity of steel I-girder bridges
-
Shota Yamanaka Punching shear resistance of synthetic floor slabs for large aircraft loads
-
Yuya Yamamoto Research on micro-corrosion environments of steel structures and evaluation methods for corrosion damage over time
-
Lee Hongbin Development of bridge inspection roads and bridge expansion devices using GFRP materials
-
-
Hideo Kajiwara Evaluation of punching shear strength of RC slab using short fiber reinforced lightweight type 2 concrete
-
Taiki Shiro Research on the fatigue behavior of the deck plate and U-rib welded part of the steel floor slab
-
Koki Sugiyama Adhesion characteristics of reinforcing interfaces of RC members using CFRP grids and CFRP strand sheets
-
Sho Takita Shear strength of steel fiber reinforced lightweight type 2 concrete RC beams using CFRP shear reinforcing bars
-
Yuki Mukaigawa Fundamental research on evaluation methods for aging corrosion damage to steel members that occurs and progresses from coating film defects
-
-
Kunihiro Sugitani Atmospheric corrosion environment using ACM type corrosion sensor and corrosion product thickness and evaluation method of corrosion depth over time of ordinary steel plate
-
Toru Omoto Research on the strength and durability of joints of GFRP pultruded members
-
Takatomo Sonoda Punching shear resistance of RC slabs using steel fiber reinforced lightweight type 2 concrete
-
Vudatvan Research on spatial statistical numerical simulation method for corrosion behavior of steel structural members over time
-
-
Satoshi Onoe Research on the fatigue behavior of the weld between the deck plate and U-rib of the steel deck
-
Hiroto Katsuki Fundamental research on corrosion pitting engineering model of steel in atmospheric corrosion environment
-
Tomohisa Choi Mechanical Properties of Steel Fiber Reinforced Lightweight Class 2 Concrete and Evaluation of Shear Strength of RC Beams
-
Yohei Torisu Investigation on strength characteristics of CFRP and evaluation of shear strength of RC beams using CFRP
-
Dai Miyazaki Research on changes in waterfront use of the Naka River and Hakata River in central Fukuoka and its factors
-
Seiki Yoshioka Research on a Design Support System for Public Works Combining the Advisor System and the Committee System -A Case Study of the Nagasaki Prefecture Public Works Design Evaluation System-
-
Le Tung Phuong Research on the shear adhesion properties of carbon fiber sheets and steel plates
-
-
Nobuaki Konomi Post-evaluation of the walking function of a universal design sidewalk that does not use guiding blocks -A case study of the Sakaejo Tameishi Line in Nagasaki-
-
Atsushi Goto Research on the evaluation of the influence of the atmospheric microenvironment on the corrosion behavior of steel
-
Masatoshi Tachikake Research on the stress transmission mechanism of the grid points of composite truss bridges
-
Shintaro Hayashi Research on the formation process of green promenades in the city center of Fukuoka City
-
-
Kenji Kobayashi Experimental study on load-bearing behavior of GFRP pultruded beams and their joints
-
Fumiko Taura Analysis of User Behavior Characteristics on a Riverbed Gently Sloping Slope -A Case Study of the Onga River Nogata District River Improvement Project-
-
Tomoki Takebayashi Research on the state of preservation of historic stone walls and public awareness in Izuhara, Tsushima City
-
Daiyu Nakagawa: A study on the applicability of a land use adjustment system based on community participation in urbanized areas
-
Yoshiyuki Nagata Research on peel strength in punching shear of reinforced concrete floor slabs
-
Junpei Noguchi Effects and issues of resident participation from the planning stage to the implementation stage in a regional trunk road widening project
-
Kenichi Miura Fundamental research on the fatigue behavior of the deck plate and U-rib welded part of the steel floor slab
-
Chihiro Mutaguchi A case study on the administrative coordination process for park-like use of urban road spaces -Sapporo, Sendai, Nagoya, and Hiroshima-
-
-
Kazuhiko Ito A case study on how to introduce landscape design in road bridge construction projects
-
Midori Enomoto Fundamental research on asset valuation methods for urban bridges
-
Ryohei Okamoto A case comparison of the design and operation of a system aimed at creating detailed district plans through the participation of residents -Case studies of Kobe City, Hyogo Prefecture and Shima Town, Fukuoka Prefecture-
-
Shenghua Guo Research on the stress transmission mechanism of the corners of composite rigid frame bridge piers with upper and lower rigid connections
-
Nawar Bitter FUNDAMAENTAL CHARACTERISTICS OF NEW CFRP RODS WITH U-END ANCHOR FOR APPLICATION TO PRESTRESSED CONCRETE STRUCTURES
-
Hironori Hayashi Research on how local residents perceive the creek landscape in the Saga Plain
-
Keita Fukui Research on shear strength evaluation of ultra-lightweight RC beams reinforced with steel fibers
-
-
Tomoya Ishibashi Fundamental research for building a design theory for pedestrian bridges
-
Daifang Luo Considerations on the impact of roadside trees on urban development-a case study of Keyaki-dori Street in Fukuoka City-
-
-
Kazuhiro Katabuchi Research on the load-bearing characteristics of concrete-filled steel pipe (CFT) arch ribs
-
Naoyuki Sato: Research on urban river improvement that promotes urban revitalization
-
Ryohei Takita Experimental study on the mechanical properties of ultralight concrete composite beams using long deformed reinforcing bar dowels
-
Masahiko Manabe Research on urban center development utilizing existing open space stock
-
Mariko Yoshihara Research on Resident Participation in Regional Arterial Road Widening Projects Penetrating Existing Communities
-
-
Takeshi Inoue Basic research on the application of the UCAS construction method and ecocement to concrete structural members
-
Yusuke Onoe Research on bending shear properties of steel/ultralight concrete composite beams using anti-slip bars as shear reinforcing bars
-
Makoto Kaida Anti-slip and punch-out shear properties of truss rebar half-prefabricated synthetic floor slabs
-
Kazuaki Sagawa Experimental research on the application of CFRP rods to thin concrete members
-
Hideki Noda Research on the transition of open space policies and the open space formation process in the city center of Fukuoka City
-
-
Takashi Kodama Research on the structural characteristics of half-prefabricated composite floor slabs with truss reinforcing bars
-
Keitaro Samizo Research on the application of non-curing continuous carbon fiber reinforcement to concrete structures
-
Yusuke Takahashi Research on the maintenance and management of rural landscapes in suburban areas -A case study of the Sakurai district of Shima-cho, Itoshima-gun, Fukuoka-
-
Takaaki Miyoshi Research on the creation of amenities on pedestrian bridges
-
-
Naoya Ikemura Experimental research on reinforcement of existing RC deck steel girder bridges using glass fiber reinforcement
-
Yuichi Kobayashi Fundamental research on the mechanical properties of concrete beams using the UCAS method
-
Masaaki Honda Building a landscape evaluation system for the purpose of maintaining and nurturing rural landscapes
-
Hiroki Goda Basic research on steel composite girders using channel-type precast PC slabs and their weight reduction
-
-
Takahiro Kawasaki Research on the effect of improving port functions using a port-to-port transport model for each item
-
Takahiro Kitamura Experimental research on joints of GFRP reinforcing materials used for floor slab reinforcement of existing steel bridges
-
Takafumi Araya Physical properties of steel-concrete composite members using ultralight concrete
-
Tatsuyuki Yamane A study on the elastic-plastic behavior and earthquake resistance of multi-column composite piers using concrete-filled steel pipe columns
-
Doja Maruddin Rudi Application of Unresin Continuous Carbon Fibers as Flexural Reinforcement in Concrete Structure
-
-
Kentaro Kawakami Research on the shape of urban viaducts that are in harmony with the surrounding environment
-
Ichiro Kono Research on the bending and shearing shape of steel frame piers with R
-
Hiroshi Kinoshita Research on the application of channel-type precast PC floor slabs to steel composite girders
-
Takafumi Yamauchi: Basic research on the effects of improving port functions using an item-specific port-to-port transportation model
-
Xu Shengzhuo Fundamental research on bridge axial joints for road bridge composite slabs
-
-
Shinji Kizaki Research on the behavior and design of the joints of main columns and struts in multi-column composite piers
-
Hideki Tonouchi Research on fracture behavior and shear strength of RC deep beams with shear reinforcing bars
-
Yasunori Nishikawa Research on the effect of improving port functions considering the port selection behavior of shippers and shipping companies
-
Satoshi Baba Research on load-bearing capacity and deformation performance of steel pier columns with curvature at cross-sectional corners
-
Basem Abdullah Strengthening of steel I-girder bridge with RC slab by GFRP members
-
-
Susumu Iguchi Research on quantitative evaluation of the landscape of urban viaducts
-
Hiroyuki Ikeda Optimizing and economic evaluation analysis of new transportation and transport system route network construction plans using M.E.-type linear
-
Takeyuki Shishida Research on Multipurpose Optimal Design of Multi-Column Composite Bridge Piers
-
Takashi Nagahama Research on bending and punching shear properties of concrete slabs using two-dimensional grid-like continuous fiber reinforcement (CFRP net)
-
Yoshiyuki Fukunaga Research on fracture behavior of RC deep beams and their strength evaluation
-
Yoshinori Yamaguchi Bending properties of CFRP reinforced concrete beams under high heat load
-
-
Hideki Okuda Research on optimal design of multi-column composite piers using genetic algorithms
-
Makoto Kondo: Basic research on the mechanical properties of prestressed synthetic plates and their joints
-
Nobuhiro Dozono Experimental study on fatigue properties of pier directional joints of road bridge composite slabs
-
Yuji Masukawa Research on temperature and mechanical properties of CFRP reinforced concrete beams heated to high temperatures
-
-
Hironori Ishibashi Non-linear finite element analysis of concrete structural members using embedded rebar model
-
Nobuyuki Kawano Research on bi-directional creep properties of prestressed steel plates and composite concrete slabs
-
Takeshi Yamada Research on structural characteristics and design methods of continuous composite slab bridges filled with hard urethane
-
Keisuke Yonekura Research on system analysis as a new means of transportation using the Marine Express Maglev
-
Lee Chong-hwan Research on shear reinforcement effect of reinforced concrete beams by carbon fiber net
-
Moto Obuchi Design and analysis of structures using the strut-tie model
-
-
Kensuke Arase Research on the application of lightweight composite slab bridges to recycling bridges
-
Yasuhiro Oka Mechanical properties of thin-walled RC frame composite structural members reinforced with carbon fiber net
-
Toru Yano Research on prestressed steel plate/concrete composite beams and introduction prestress of composite plates
-
Tang Jialin 3D seismic response analysis of pile-supported bridge piers by concentrated mass method
-
-
Kazuhisa Okamoto Research on bi-directional prestressing of steel plate and concrete composite plate
-
Kazuaki Yokoyama Fundamental research on shear reinforcement effect of reinforced concrete beams by carbon fiber net and reinforcement of perforated reinforced concrete beams
-
-
Shigeo Niinishi <under investigation>
-
Fumitaka Katabuchi Research on impact resistance of synthetic structural members using lightweight fillers
-
Tomohiko Hiroshige Research on the mechanical properties of perforated beams reinforced with carbon fiber nets
-
Junichi Hoshikuma Research on bi-directional prestressing of steel plate and concrete composite plate -development of bi-directional steel plate tensioning device-
-
-
Shunichi Onitsuka Research on the design and construction of composite I-girder bridges using TSC deck slabs and their structural characteristics
-
Hideki Kaji Research on prestressing of steel plate/concrete composite beams and their static bending properties
-
-
Hidekazu Kanezawa Investigation of fatigue behavior of TSC composite floor slab by moving loading method
-
Ichiro Kuroda Basic research on temperature stress characteristics of steel-concrete composite members
-
-
Tadashi Waki Naga Static bending properties of TSC composite members using ultra-high-strength concrete
-
-
Masahiko Iguchi Fundamental research on the fatigue behavior of TSC synthetic plates and fatigue design methods
-
Toru Sasaki Research on three-dimensional heat conduction in synthetic beams
-
Masaharu Shigetome Economic Comparison of Cable-Stayed Bridges with Different Main Girder Types
-
-
Shinichi Kim Research on the mechanical characteristics and design method of composite slab bridges
-
Takatoshi Tajima Research on optimal elasto-plastic design of curved box girder bridges
-
-
Taiji Yasuda Research on static and dynamic fatigue properties of composite floor slabs with three-dimensional truss-type dowels
-
-
Masami Koshiishi Fundamental research on the mechanical behavior of synthetic floor slabs with three-dimensional truss-type dowels
-
Takayuki Nose Experimental study on the impact bending properties of mortar reinforced with spiral fibers
-
Kenji Horinouchi Experimental study on complex nonlinear behavior of arc girder and arc lattice girder
-
Takeshi Yoshida Research on the mechanical characteristics of multi-cable long cable-stayed bridges with different main girder support systems
-
-
Nozomi Mori Research on the collapse behavior of curved girder bridges with thin open cross sections
-
-
Akihisa Ayame Research on the steel joint structure of precast composite floor slabs
-
Hiroyasu Tajima Plastic analysis method for plate structures
-
-
Hiroyuki Udagawa Research on the boundary element method in thermal and elastoplastic deformation
-
Akiyoshi Kawamura Research on horizontal loading test of RC high bridge piers
-
Tadao Kubo Research on local buckling and ultimate strength of curved I-girders subjected to equal bending
-
-
Tsunemitsu Kaneko Elastic-plastic analysis of arc curved girder with thin box cross section
-
-
Ichiro Hirose Research on elasto-plastic analysis of steel box girders subjected to combined loads
-
-
Yakuro Inoue About the behavior of connecting beams subjected to repeated loads and the incomplete rigid bonding properties of joints
-
Kazumi Tamura Elastic-plastic analysis of thin steel box girder bridges using the finite strip element method
-
Kazuhisa Fujisaki Elastic-Plastic Large Deflection Analysis of Plane Frame Structures Subjected to Bending and Axial Force
-
-
Norio Ogata Research on elasto-plastic behavior of long suspension bridges
-
Shinichi Hino Research on bending strength of RC and PC girders connected by steel joints
-
Kenzo Fujioka Elastic-plastic analysis of thin box girders subjected to arbitrary combined loads
-
-
Seiji Iwataki Research on fracture resistance and deformation properties of reinforced concrete joint girders with steel joints
-
Keiichiro Teramoto Automatic limit analysis method for framework structures
-
-
Toshiro Akeda Fundamental research on elastoplastic deformation behavior analysis of suspension bridges
-
-
Shunpei Takeuchi Fundamental research on the water absorption and retention properties of crosslinked acrylate fibers
-
-
Hiroki Hashimoto Fundamental research on the applicability of sacrificial anodic corrosion protection technology for clogging parts
-
Takumi Inoue Basic research on the durability and anti-corrosion performance of overlapping parts of metal thermal spray coating and heavy anti-corrosion coating
-
-
Keisuke Suzuki Fundamental research on the sacrificial anti-corrosion effect of zinc-rich paint against steel corrosion between paint film scratches
-
Aoyuki Tanaka Fundamental research on the durability and anti-corrosion performance of the layered part of the metal thermal spray coating and the heavy-duty anti-corrosion coating
-
Kaiji Takagi Fundamental research on applicability of atmospheric sacrificial anodic corrosion protection technology to deteriorated parts of Al-Mg alloy thermal spray coating
-
-
Kazuya Arishima Fundamental research on salt adhesion properties in a quantitative salt adhesion method using ultrasonic atomization
-
Saki Okada Basic research on corrosion behavior of spheroidal graphite cast iron in atmospheric environment
-
-
Ryo Higuchi: Fundamental research on the electrochemical mechanism of steel corrosion between adjacent paint film scratches in a standing water environment
-
Shoma Iio Research on the effect of different corrosion environments on the anticorrosion effect of atmospheric sacrificial anodic corrosion protection
-
-
Yui Jiromaru Fundamental research on the development of an improved loop joint structure for precast PC floor slabs
-
Ryo Namiki Research on the impact of high speed on the side of the reinforcing bar behind the PCM winding method
-
Takeshi Kaneko Effect of the type of abrasive on the surface properties of the blast steel substrate preparation and the adhesion properties of the anti-corrosion coating
-
Tomoki Takeda Fundamental research on corrosion behavior over time in atmospheric environments of unpainted weathering steel with a focus on pitting corrosion resistance
-
Takashi Hasegawa Fundamental research on the electrochemical mechanism of steel corrosion between adjacent paint film scratches during the water film drying process
-
Yusuke Mizukami Basic research on sacrificial anodic corrosion protection technology for closed parts of steel members using Al-Zn alloy casting materials and fibers
-
-
Shunta Sakurai Improvement of adhesion performance by inserting polyurea resin in CFRP plate adhesion reinforcement method
-
Ikuo Tadakuma Experimental research on the anchorage length of reinforcing bars in the PCM winding reinforcement method
-
Eitai Tachibana Fundamental research on material mechanics performance of concrete used in joints of precast members
-
Keita Tanigawa Investigation of the effect of laser surface preparation on the surface properties of steel materials and coating adhesion performance
-
Fumi Yamagata Research on methods for evaluating and predicting the corrosion behavior of steel structural members using ground sensors
-
Kazuya Yamashita: Fundamental research on sacrificial anodic corrosion protection technology in closed cross-sections of steel members using Al-Zn alloys and fibers
-
Liu Shaobo Research on anti-corrosion and anti-corrosion properties of hot-dip galvanized films in highly corrosive environments due to chlorides
-
-
Katsuya Hirose Basic research on galvanic corrosion characteristics of Al-Mg alloy thermal spraying/Zn plating/thermal spraying
-
Koshiro Ikemoto Reinforcement effect of PCM spraying method for low rebar ratio RC beams where bending and shearing act simultaneously on joints
-
Kosuke Yagi Evaluation of the effect of heat capacity on the corrosion behavior of bare ordinary steel sheets in an atmospheric environment
-
Gaku Masumoto: Fundamental research on the electrochemical mechanism of steel with adjacent coating scratches
-
Masaya Ishimura Bending load bearing behavior of various joining methods for precast box culverts
-
Hiroyuki Momota: Fundamental research on corrosion surface properties and fatigue behavior of finger joints for bridges with corrosion damage
-
Takahiro Ogi Shear reinforcement effect of RC beams by PCM spraying method using CFRP grid
-
-
Nako Moriga Evaluation of shear reinforcement of RC members in CFRP grid PCM spraying method
-
Minami Hirao Fundamental research on corrosion evaluation methods for steel structures considering heat capacity
-
Shoma Yamashita Bend and shear reinforcement effect of low reinforcement ratio concrete members with joints by PCM spraying method
-
Masahiro Watanabe Experimental research on bending characteristics of member joints by precast PC crimping method
-
Ryota Watanabe Evaluation of the impact of physical and chemical base preparation on the surface properties of steel materials and the adhesion performance of coating films
-
Takushi Fujimoto Basic research on atmospheric sacrificial anodic corrosion protection technology for corroded steel members using Al-Zn alloy casting materials and fiber sheets
-
-
Takuya Okamoto Floor slab bending reinforcement effect with high-strength panels
-
Takumi Kai Compression softening behavior of short fiber reinforced lightweight type 2 concrete
-
Aki Kanamaru Shear reinforcement effect of sluice box partition wall by CFRP grid
-
Yosuke Kinoshita Evaluation of stress properties and fatigue durability of steel floor slab deck plates with corrosion damage
-
Junji Kobayashi Fundamental research on the effect of the proximity of coating film defects on the corrosion behavior of steel
-
Yohei Tsuchibashi Fundamental research on the effect of adhesion and deposits on the corrosion behavior of steel
-
Yusuke Miura Load-bearing characteristics of precast arch culverts using prestressed structures
-
Masatsugu Michino Comprehensive quantitative evaluation of corrosion at the site level of unpainted weathering steel bridges
-
Hironobu Yuno Tensile properties and joint properties of CFRP rods
-
-
Kohei Ibusuki Evaluation of the impact of corrosion damage on the fatigue durability of steel deck deck plates
-
Hiroki Goda Experimental study on corrosion behavior of steel sheets progressing from coating film defects over time
-
Sota Saito Research on bending reinforcement effect of plain concrete members by PCM spraying method
-
Junji Tsurumaru Research on shear reinforcement effect of RC members by PCM spraying method of CFRP grid
-
Yosuke Hori Research on load bearing and temperature stress characteristics of composite slab bridges using large aircraft loads
-
-
Takefumi Shigeto Seismic reinforcement of dam piers using the PCM spraying method
-
Daiki Takushima: Development of bridge expansion devices using GFRP material
-
Hideyuki Hayashi Research on micro-corrosion environment evaluation of structural members of steel truss bridges in airborne salt environments
-
Taiga Hirai Analytical study on the effect of the remaining part of the hanging hardware for erection of steel deck bridges on the occurrence of fatigue damage
-
Shintaro Yasuda Punching shear strength of RC plate using short fiber reinforced lightweight type 2 concrete
-
-
Tomohiko Naono Research on the application of GFRP pultruded materials to bridge inspection roads
-
Kazuya Matsuo Fundamental research on atmospheric sacrificial anodic corrosion protection technology for corroded steel members
-
Masahiro Ishimoto Development of bridge expansion device using glass fiber reinforcement
-
-
Kazuhiro Utsunomiya Fundamental research on sacrificial anodic corrosion protection technology for steel members in atmospheric environments
-
Yusuke Kato Basic research on spatial statistical analysis of corroded surface properties of steel members for the purpose of repair and reinforcement
-
Shota Yamanaka Shear capacity of lightweight Class 2 concrete RC beams using CFRP shear reinforcing bars
-
Yuya Yamamoto Basic research on evaluation of corrosion behavior over time of unpainted weathering steel and determination of protective rust formation
-
-
Yoshihiro Aramaki Research on changes in the design concept of sluice gates - Focusing on the Chikugo River and Yabe River -
-
Daisuke Ushibo Research on landscape structure of impressive scenery on mountain railways -Takachiho Line as a case study-
-
Hideo Kajiwara Bending Behavior of Steel Fiber Reinforced Lightweight Class 2 Concrete Composite Girder Using Perforated Steel Plate Dowel
-
Daiki Shiro Mechanism of occurrence of fatigue damage and repair and reinforcement methods in floor assembly connection plate welds
-
Sho Takita: Shear strength evaluation of RC beams using CFRP shear reinforcing bars
-
Yuki Mukaigawa Research on the evaluation of the effects of differences in salt corrosion environments on the aging corrosion surface properties of steel
-
-
Toru Omoto Experimental research on strength characteristics of GFRP/steel joints using adhesive and bolt joints
-
Kunihiro Sugitani Evaluation of output variation and deterioration characteristics of the ACM type corrosion sensor
-
Takatomo Sonoda Research on displacement characteristics of perforated steel plate dowels using ultralight concrete reinforced with short fibers
-
Noriyuki Tsutsui A study on the effect of using a model at the basic design stage of a river improvement project with citizen participation-a case study of the Ongagawa Nogata district-
-
Kana Watanabe The historical transition of efforts to create pine groves through citizen participation in Rinkai Park
-
Vudatvan Numerical simulation of corrosion surface properties of steel exposed to the sea
-
-
Yohei Torisu Experimental study on the strength characteristics of the U-shaped anchor part of CFRP (UCAS) rods
-
Hiroto Katsuki Research on performance evaluation of microcapsule crack detection materials and applicability to actual structures
-
Satoshi Onoe Building a test system for fatigue cracks in the weld root of the deck plate and U-rib of the steel deck
-
Seiki Yoshioka Research on the landscape advisor system in public works
-
Le Phuong Tung Bending Reinforcement Effect of RC Beams by Adhesion of Sides of Glass Fiber Sheets
-
-
Nobuaki Konomi Experimental research on the tensile properties of automatically manufactured CFRP rods and their applicability to PC beams
-
Jun Goto Numerical simulation of corrosion surface properties of steel exposed to the sea
-
Hiroaki Shoji Basic research on fatigue crack detection methods using microencapsulated paint
-
Masatoshi Tachikake Experimental study on mechanical properties of glass fiber reinforced material I-600 by pultrusion molding
-
Shintaro Hayashi Typology of Vista Landscape Transformation in Castle Town Karatsu
-
Dai Miyazaki Research on the relationship between urban formation and waterfront use around the Hakata River since the modern era
-
-
Hiroyuki Kuryu Grasping the existence of creeks in the Saga Plain and design proposals for repair and maintenance
-
Akitoshi Katayama Research on the shear behavior of SRC horizontal beams and the stress transmission mechanism of corners
-
Fumiko Taura Towards the preservation of Japan's oldest existing steel girder road bridge Meiji Bridge
-
Tomoki Takebayashi Evaluation of shear strength of RC beams using ultralight concrete reinforced with short fibers
-
Satoshi Nakamura Experimental study on bending and shear properties of glass fiber H-section beams
-
Chihiro Mutaguchi Comparison of open space measures in urban areas of ordinance-designated cities
-
-
Ryohei Okamoto Research on resident-centered regional development based on the Shima-machi, Fukuoka Prefecture "Ordinance for Town Development for Rural Residence"
-
Midori Enomoto: Experimental research on reinforcement method for rebar-embedded polymer cement mortar for existing RC bridge piers
-
Tomoko Sasaki Research on the positioning of bicycles in urban centers in Japan and the Netherlands
-
Eri Tsugami Basic research on the application of CFRP rods with U-shaped anchors to PC members
-
Keita Fukui Experimental research on evaluation of shear strength of ultralight RC beams reinforced with short fibers
-
Tomohiko Maekawa Experimental research on the stress transmission mechanism of the corners of RC rigid frame piers penetrated by steel I main girders
-
-
Tomoya Ishibashi Research on the expansion of design freedom seen in new pedestrian bridges in recent years ~Case study of "BRIDGEBUILUDERS"~
-
Tomoko Ushijima Research on the bending properties of eco-cement concrete beams using continuous carbon fiber as reinforcing bars
-
Kenichiro Sakata Mechanical properties of ultralight reinforced concrete beams reinforced with short fibers
-
Ryohei Tamaogi Experimental study on the mechanical properties of CFRP rods with internal restraining force
-
Yasunari Hirahara Analytical study on the reinforcement effect of existing steel girder bridge RC floor slabs using glass fiber continuous reinforcement members
-
Akiko Matsumoto Basic research on bending properties of thin concrete members using continuous carbon fiber reinforcement
-
-
Takaharu Imai Experimental research on the manufacturing method and mechanical properties of concrete structural members using the UCAS method
-
Kazuhiro Katabuchi Positive and negative cyclic loading experiments on multi-column composite bridge piers using concrete-filled steel pipes
-
Naoyuki Sato Research on rural landscape simulation methods seen from the perspective of pedestrians -A case study of the Sakurai district of Shima-cho, Itoshima-gun, Fukuoka-
-
Ryohei Takita Experimental study on the application of ultralight concrete reinforced with short fibers to synthetic structural members
-
Masahiko Manabe Research on the design and landscape of lightweight and thin prestressed concrete structures <
-
-
Takeshi Inoue Comprehensive survey on the usefulness of the UCAS construction method by fuzzy multi-criteria analysis and its demonstration experiment
-
Yusuke Onoe Research on load-bearing performance and fatigue durability of improved PRC structural joints in channel-type precast PC floor slabs
-
Makoto Kaida Structural characteristics of truss rebar half prefabricated composite floor slab erection system and completed system
-
Kazuaki Sagawa Research on the effect of improving port functions using a transport model between ports
-
Hideki Noda Research on improving the usage of Fukuoka City Kego Park
-
-
Daimoto Kiwaki Experimental research on the joint structure of road bridge composite floor slabs using tension bolt joints
-
Takashi Kodama Research on the thermal effects of synthetic I-girder bridges associated with the replacement of existing RC floor slabs
-
Keitaro Samizo Anti-slip properties of studs in composite structures using ultralight concrete
-
Yoshisuke Takahashi: A study on how environmental symbiosis-type development should be in suburban rural areas
-
Takaaki Miyoshi Research on the use of landscape image perspectives for the purpose of preserving rural landscapes
-
Takashi Yamazaki Experimental research on anti-slip properties due to the shape of the lower surface of the channel-type precast PC floor slab
-
-
Naoya Ikemura Basic research on reinforcement of existing RC deck steel girder bridges with glass fiber reinforcement
-
Yuichi Kobayashi Static bending properties of concrete beams reinforced with continuous and short fibers
-
Hiroki Goda Experimental research on bending fatigue properties of steel composite girders using channel-type precast PC slabs
-
Noryati Mohamad Amin Research on comparison of high-density container stockyard system and straddle carrier system in port cargo handling system
-
Masaaki Honda A study on the landscape of cable-stayed bridges applying the aesthetic harmony ratio
-
-
Takahiro Kawasaki Fundamental research on harbor container transportation systems by introducing linear carts
-
Tetsuji Kawasaki Study on the creep properties of prestressed synthetic slabs and their application to actual structures
-
Takahiro Kitamura Experimental study on the reinforcement effect of steel bridge RC floor slabs with GFRP members
-
Kazutaka Sakajiri Research on deformation properties of concrete members using continuous carbon fiber reinforcement
-
Takafumi Shinya Experimental research on the load-bearing capacity and deformation performance of beams and corners of Rahmen bridge piers made of steel
-
Shinya Takeshita Load test of a lightweight synthetic slab bridge (recycling bridge) that reuses empty cans
-
Tatsuyuki Yamane Research on the ultimate behavior of multi-column composite piers
-
-
Kentaro Kawakami Research on landscape evaluation of urban viaducts with integrated upper and lower structures
-
Ichiro Kono Model test of joints of multi-column synthetic elevated legs using concrete-filled steel pipe columns
-
Ken Hirano Negative bending countermeasures for continuous composite slab bridges using hard urethane as a filler
-
Takashi Yamauchi Research on forecasting port areas by introducing high-density container stockyards
-
-
Yoshihisa Ada Investigation of negative bending behavior of intermediate fulcrums in continuous composite slab bridges
-
Shinji Kizaki Effect of shrinkage reducing agents on creep and effective prestress of steel plate/concrete composite beams
-
Hideki Tonouchi Experimental study on fracture behavior of RC deep beam with end restraint
-
Yasunori Nishikawa Research on the effects of introducing a new logistics system using M.E.-type linear
-
Satoshi Baba Research on quantitative evaluation methods for the landscape of urban viaduct substructures
-
Takuya Ogawa Bending behavior of concrete floor slabs using two-dimensional lattice continuous reinforcement
-
-
Susumu Iguchi <under investigation>
-
Hiroyuki Ikeda Economic evaluation analysis of a new transportation system using M.E.-type linear using Fuzzy theory
-
Takahiro Ito Mechanical characteristics and trial design of a two-span continuous lightweight synthetic slab bridge filled with hard urethane
-
Takeyuki Shishida Static structural characteristics of multi-column composite piers using concrete-filled steel pipe columns
-
Hikaru Hayakawa Investigation on the application of prestressed steel plates and composite concrete slabs to civil engineering structures
-
Yoshiyuki Fukunaga Ultimate strength analysis of RC deep beam using strut-tie model
-
Shunichiro Furusawa Feasibility Study of Marine Express Maglev New Traffic/Transportation System for Kyushu, Japan, and South Korea
-
Yoshinori Yamaguchi Non-linear finite element analysis of carbon fiber net reinforced concrete members using embedded rebar model
-
-
Koichiro Aidani <under investigation>
-
Hideki Okuda Fundamental research on the development of multi-column high bridge piers using concrete-filled steel pipe columns
-
Makoto Kondo Prestressed steel plate/concrete composite beam and creep behavior of composite plate
-
Nobuhiro Dozono Experimental research on the application of steel-concrete composite slab bridges using lightweight fillers to continuous bridges
-
Yoshiyasu Fujise Feasibility Study for Fukuoka City on New Logistics System Using M.E.-type Maglev
-
Ichiro Misumi Development of a lightweight composite slab bridge that reuses empty cans
-
-
Soji Oshiro Fundamental study on bi-directional creep behavior of prestressed steel plates and composite concrete slabs
-
Nobuyuki Kono Loading test of curved synthetic I-girder bridge (Shinden No. 2 bridge) using TSC synthetic slab
-
Akihiro Sasayama Park landscape design for Uminonakamichi Seaside Park
-
Shiro Doi Fatigue strength of steel plate/concrete composite beam with steel plate stamping TSC
-
Takeshi Yamada Static punching shear properties of synthetic floor slabs using lightweight filler
-
Keisuke Yonekura Research on Economic Evaluation Analysis of Logistics System by Marine Express Maglev
-
-
Kensuke Arase Feasibirity Study of Next Generation Logistics System by Amphibious (Marine Express Type) Maglev
-
Yasuhiro Oka: Elastic-plastic finite element analysis of perforated concrete girders reinforced with thin films
-
Satoshi Kamiishida Research on structural characteristics of synthetic I-girder bridges using TSC deck slabs
-
Kuninori Kudo Research on the transfer effect of prestressed synthetic beams using steel sheets as tendons
-
Toshio Sugiyabu Research on the environmental improvement effects of next-generation logistics systems using amphibious linear systems and their evaluation
-
Shoichiro Nagasaki Research on the mechanical properties of concrete under high temperature load
-
Shinichi Horinouchi Research on the use of carbon fiber net materials to reduce the weight of PC bridges
-
Toru Yano Building a traffic volume distribution model in mixed traffic flow and research on its characteristics
-
-
Hisato Ishii Measurement of various constants of concrete under high temperature and analysis of heat conduction and temperature stress of RC beams
-
Hideaki Ota Application of the minimum cost design method to PC cable-stayed bridges
-
Kazuhisa Okamoto: Fundamental research on bi-directional prestressing of steel plate/concrete composite plate members
-
Koichiro Kakurezuka Properties of composite beams of steel plates and concrete using lightweight fillers
-
Kiyoshi Hiwada Fundamental research on the use of new materials to reduce the weight of PC box girder bridges
-
Kazuaki Yokoyama A study on weight reduction of PC box girder bridges using composite structural struts
-
-
Shuo Kashima About the structural characteristics of the Marine Express guide system
-
Katsuaki Kaneda Research by heat conduction analysis of concrete structures
-
Shinji Takada Research on the design shear force of space truss type dowels
-
Tomohiko Hiroshige Finite element analysis of concrete structures using embedded rebar models
-
Hiroki Furuya Research on prestressing steel plates and composite concrete slabs - Introduction of prestress and bending properties of PST composite beams -
-
Junichi Hoshikuma Research on prestressing of steel plates and composite concrete slabs -changes in prestress introduced over time-
-
-
Hisashi Inohata Research on the buckling load capacity of TSC steel plates as main girder compression flanges
-
Hiroshi Okamura Experimental research on punching shear resistance of space truss type dowels
-
Shunichi Onitsuka Static Bending Properties of TSC Synthetic Slab with Closed Portion
-
Hideki Kaji Fundamental research on prestressing methods for TSC composite panels
-
Fumitaka Katabuchi Static and Fatigue Tests of Steel/PC Composite Beams Using Mixed Structural Forms
-
Naotoshi Kanamaru Research Approach to the Marine Express Concept
-
Kiyoshi Kawano Finite element analysis of synthetic slab structure with three-dimensional truss type dowel
-
-
Michio Ogawa Research on numerical analysis methods for synthetic structures with space truss-type dowels
-
Ryuji Okita Influence of bonding surface painting on the mechanical properties of TSC composite members
-
Teppei Kai A study on the economic efficiency of synthetic continuous girder bridges
-
Hidekazu Kanezawa Fatigue Properties of Ribbed TSC Synthetic Beams
-
Ichiro Kuroda Basic research on the thermal effects of concrete
-
Akihiro Nagahama Research on the buckling load resistance of steel plates with three-dimensional truss type dowels
-
-
Masayuki Ueno Static dynamic characteristics of a cable-stayed bridge with a V-type main tower
-
Teraoka Atmosphere Fundamental research on heat conduction in RC and synthetic beams subjected to high-temperature heat loads
-
Hiroshi Hata Static mechanical characteristics of space truss type composite girder with dowel
-
Toshihiro Hara Bending fatigue property of synthetic slab with space truss type dowel
-
Hideto Miyatake Research on applicability of simple plastic analysis method to curved girder bridges
-
Tadashi Waki Naga About stress evaluation of synthetic slabs with three-dimensional truss-type dowels
-
-
Masahiko Iguchi Fatigue characteristics of composite floor slabs with three-dimensional truss-type dowels
-
Yoshihiro Iwakuma Theoretical and experimental research on the yield function of thin curved I-girders
-
Toru Sasaki Experimental study on shear strength of plane and space truss type dowels
-
Koichi Sueyoshi Mechanical characteristics and economic efficiency of composite cable-stayed bridges
-
Sadao Harada Research on the load-bearing capacity of thin curved I-girder bridges and its estimation method <
-
-
Hajime Inoue About the influence of the floor assembly on the load-bearing capacity of a parallel curved I-girder bridge
-
Yoichi Okada, Tsuyoshi Takayanagi Experimental research on synthetic floor slabs with three-dimensional truss-type dowels
-
Tetsuya Migita Experimental study on bending toughness of mortar reinforced with spiral fibers
-
Toshiyuki Koga Fundamental research on reliability analysis methods for structural systems
-
Yoshiomi Sonoda Non-linear behavior characteristics of long cable-stayed bridges
-
Takatoshi Tajima Experimental study on elasto-plastic behavior of parallel curve I-girder bridges
-
Naotsugu Yoshida Evaluation of allowable stress design method by second moment method
-
-
Kenji Iino Research on bending fatigue properties of precast composite floor slabs with steel joints
-
Akiyasu Eto Fundamental research on the bending properties of mortar reinforced with spiral fibers
-
Kazuhiko Kato Research on the optimal fixing method for multi-cable long cable-stayed bridges
-
Kazunori Takayama Cable-stayed bridge tower and railing design
-
Yoshinori Takeda Research on the collapse behavior of continuous curve box girder
-
Hiroyasu Ogura Research on structural characteristics of partially anchored multi-cable long cable-stayed bridges
-
Taiji Yasuda <under investigation>
-
-
Shoichi Ohno Research on limit state design methods for steel structures
-
Masami Koshiishi About the applicability of the plastic hinge method to the problem of plastic bending of flat plates
-
Takeshi Yoshida Designing a plate girder using a discrete optimization method
-
Masao Tominaga Analysis of elasto-plastic deformation behavior of RC bridge piers with seismic walls
-
Shunsuke Sanada Basic research on the steel joint structure of precast PC members
-
Kenji Horinouchi Plastic Analysis Theory of Curved Girder with Thin Open Section
-
Takayuki Nose Experimental research on the joints of precast RC composite floorboards
-
-
Kengo Iwasa, Tadahiko Tsutsumi Experimental research on the joint structure of precast RC composite floor slabs
-
Amane Ouchi Restoring force characteristics of RC high piers subjected to two-way horizontal load
-
Toshinori Kuramoto On the plastic behavior characteristics of arc-curved girder bridges subjected to various loads
-
Nozomu Mori: Plastic analysis method for curved girder considering warpage
-
Toru Yoshizumi Considerations on design theory and scenery of cable-stayed bridges
-
-
Akihisa Ayame, Kazuhiko Obata Research on the mechanical properties of steel joints in precast structures
-
Mutsuhiko Otani Tension and failure experiments on box-girder curved bridges in PC 1 room
-
Isao Goto Thermal stress analysis using the boundary element method
-
Hiroyasu Tajima Ultimate analysis of a plate using the flexibility matrix method
-
Yoji Taniguchi Theoretical and experimental research on the collapse behavior of circular lattice girders
-
-
Hiroyuki Udagawa Generalization of truss girder torsion theory by virtual work method and its consideration
-
Tadao Kubo Research on local buckling due to bending of curve I girder
-
Hironori Koga Research on the mechanical properties of reinforced concrete orthogonal members connected by steel joints
-
Masaomi Koga About the collapse behavior characteristics of orthogonal lattice girders
-
Masakazu Tokuzawa About shear friction properties in steel-concrete and concrete joint surfaces
-
Kaoru Muraoka Investigation on the workability of PC connected beams and its analysis method
-
Shoji Mori: Clarification of non-linear behavior associated with fulcrum settlement and movement of a reinforced concrete arch bridge with fixed support at both ends
-
Kazuyuki Yoshioka About the collapse behavior characteristics of the two main girder circular lattice girder
-
-
Akiyoshi Kawamura Local buckling strength analysis of curved I girder flange by finite strip method
-
-
Kazuhiro Iwanaga Experimental study on shear fracture strength of reinforced concrete connecting beams
-
Tsunemitsu Kaneko Research on local buckling of steel plate structures
-
Kiyoshi Shinomiya Research on static elastic-plastic behavior of suspension bridges and main towers
-
Daisuke Sakamoto Analysis of elasto-plastic bending and torsion behavior of thin steel box girders
-
Akira Suzuki Research on the buckling behavior of steel box-shaped deformed section columns subjected to eccentric axial compressive force
-
-
Fumikazu Okai Dynamic fracture plasticity analysis of long suspension bridges
-
Kazuhisa Nishimura 3D plasticity analysis of continuous curve girder
-
Kazutoshi Hayakawa Radiative plasticity analysis of a rectangular cross-section member subjected to bending and torsional moments at the same time
-
Ichiro Hirose Analysis of shear plastic bending and torsion behavior of thin multi-chamber closed section girder by shear flow theory
-
Yukinobu Funahara Fracture plasticity analysis of cable-stayed bridges using finite deformation theory
-
Katsunori Hosoda, Ikuro Maekawa Research on bending fatigue of reinforced concrete connecting girders and stress analysis of joints
-
Yoshio Maeda Fracture plasticity analysis of beams subjected to bending and axial force by large deflection theory
-
-
Yakuro Inoue Automatic Limit Analysis Method for Lattice Girder
-
Ryoichi Shiota Basic research on bending failure of precast PC beams with joints in the middle
-
Fumio Doi: Fundamental research on methods for determining the mechanical constants of the ground and bending analysis methods for the integrated structure of the ground and piles
-
Kazuhisa Fujisaki Integral analysis method for suspension bridges considering deformation of towers and quills
-
-
Koichiro Shimoda Fundamental research on the elastic-plastic response of steel frame structures
-
Takashi Kakusho Automatic limit analysis method for straight 3D rigid frame
-
Kazumi Tamura Elastic-plastic analysis of a thin multi-chamber closed cross-section subjected to torsional moment using shear flow theory
-
Shinichi Hino Basic research on joining methods of RC girders using steel joints
-
Kenzo Fujioka Research on analytical theory of elasto-plastic bending deformation behavior of thin multi-chamber closed section girders
-
-
Seiji Iwataki Static and dynamic behavior of double-track railway truss bridges with opposite members
-
Yuji Kumano Research on dynamic elastic-plastic behavior of cantilever beams
-
Toshiaki Tasaki Theoretical consideration of the yield condition of a rectangular cross-section bar subjected to bending and torsional moments at the same time
-
Keiichiro Teramoto Automatic limit analysis of framework structures by procession
-
Shojiro Matsumoto Elastic-plastic response analysis of two-hinge arch
-